Learn which plants thrive in your Hardiness Zone with our new interactive map!

Wooden Wishing Well Instructions

By Jane Smith
Top view of a hexagonal wooden wishing well.
well image by cegli from Fotolia.com

Wooden wishing wells add fairy tale charm to your landscape. Their rustic appearance blends into any naturalized garden plan and completes an English garden or country cottage theme. A garden gnome peeking from behind the well or a resin-cast squirrel scampering along the crosspiece add humor and life to the scene.

Rough-cut logs are more rustic. Use finished logs for a more formal look.
Log Cabin image by Antonio Oquias from Fotolia.com

Cut all the 3-inch diameter rough-cut logs to 2-foot lengths on your table saw.

Make 5/16-inch holes in each end of each 3-inch diameter log section, centered 1-inch from each end, using a drill press. These are the holes for the dowel rods that will hold the base of the well together.

Lay one of the 2-foot log sections so that its length runs from left to right in front of you. Lay a second and third piece, one leaning left and one right, as if making a disconnected triangle.

Place 1/2-inch diameter dowel rods in each end of each of the three log sections. Slide the next three log sections onto the rods to form a hexagon.

All sides and interior angles are equal.
hexagone image by Unclesam from Fotolia.com

Adjust the positions of each log section until the hexagon is as regular as you can make it. Regular polygons have sides that are the same length and are set at the same interior angle to each other, according to Warren Buck, who teaches at the University Laboratory High School, University of llinois-Urbana. The distances between all opposite corners is also the same, if the shape has an even number of sides.

Continue sliding 3-inch diameter, 2-foot long log sections onto the dowel rods until all of them are connected at each end to form a hexagonal tube. This is the base of your wishing well.

Drive all the dowel rods into their holes with blows from a rubber mallet until they are flush with the top edge of the wishing well base or use a coping saw to cut them flush if you choose not to drive them into the ground. Driving them into the ground gives the base additional stability.

Cut the 2- by 3-inch rough-hewn log into three sections, 4-feet long. Stand one section upright in the right and left corners of the hexagon as it faces you. These are the uprights for the well.

Measure 6 inches and 10 inches from the top edge of the wishing well base. Drill two holes through the sides of the well base and into the uprights. Attach with 6-inch lag bolts. Lag bolts are long, thick screws with a square bolt head, once used to secure barrel staves, according to The Free Dictionary.

Find the center point of the 3rd section of 2- by 3-inch by 4-feet log. Screw the ductile iron swing hanger into the wood at that point, using manufacturer's hardware. This is your crosspiece for your wishing well.

Turn the crosspiece so that the swing hanger points at the ground. Position the crosspiece across the uprights with each end flush. Make a mark at each end of the crosspiece, 1.5 inches from each end, centered on the uprights.

Drill through the crosspiece at each mark, down into each upright. Screw a 5/16-inch diameter lag bolt into each hole.

Hang the black steel chain from the swivel using an "S" hook. Hang the cauldron from the other end of the chain, using the second "S" hook.


Things You Will Need

  • 111 rough-squared logs, 3-inch diameter, 12 feet long
  • Table saw
  • Drill press
  • 5/16-inch diameter bit
  • 6 dowel rods, 1/2-inch diameter, 4 feet long
  • Rubber mallet or coping saw
  • 1 rough-squared log, 2- by 3-inch, 12 feet long
  • 1 black ductile iron swing hanger with manufacturer's hardware
  • 4 lag bolts, 6-inch long, 5/16-inch diameter
  • 2 lag bolts, 5-inch long, 5/16-inch diameter
  • 12-inch black steel chain, 2 "S" hooks
  • Cast iron cauldron with bail

About the Author


Jane Smith has provided educational support, served people with multiple challenges, managed up to nine employees and 86 independent contractors at a time, rescued animals, designed and repaired household items and completed a three-year metalworking apprenticeship. Smith's book, "Giving Him the Blues," was published in 2008. Smith received a Bachelor of Science in education from Kent State University in 1995.