Plan the perfect garden with our interactive tool →

How to Test the Solenoid on a Kohler Lawn Mower Engine

...
multimeter image by Aleksey Bakaleev from <a href='http://www.fotolia.com'>Fotolia.com</a>

The electric starter on Kohler lawn mower engines is both a convenience and a necessity. The additional torque and compression of larger Kohler engines make it difficult to start them with traditional pull-ropes. Starters mount onto the engine block with a bendix gear positioned in such a way that it engages and spins the engine flywheel when energized. The starter solenoid serves as a relay between the lawn mower's battery and the engine starter. By turning the ignition key, the solenoid is in effect “given permission” to apply battery power to the starter motor to crank the engine. If the solenoid is suspect, troubleshoot it to confirm whether it is bad.

Clean the terminal posts on the starter solenoid. The solenoid mounts on the frame of the mower, near the engine starter. A red battery lead mounts to one of the solenoid terminals, while a second lead connects the solenoid to the engine starter.

  • The electric starter on Kohler lawn mower engines is both a convenience and a necessity.
  • The starter solenoid serves as a relay between the lawn mower's battery and the engine starter.

Test the battery lead for adequate voltage using a voltage-ohm meter. Adjust the meter to read DC voltage. Place the red lead onto the terminal of the solenoid connected directly to the battery. Place the black lead of the meter on the lawn mower’s frame as a ground reference. The voltage must read between 10 and 14 volts. If the voltage is lower than this, check and charge the battery before proceeding.

Connect a jumper lead to the solenoid terminal on the battery side of the switch. The lead runs directly from the battery to this terminal. Touch the other end of the jumper to the starter terminal post. If the engine attempts to start, the solenoid is bad and replacement with an identical replacement is necessary. If the starter does not rotate, the problem lies with the starter. Verify the battery charge again before spending the time and expense of replacing the starter.

  • Test the battery lead for adequate voltage using a voltage-ohm meter.
  • Place the red lead onto the terminal of the solenoid connected directly to the battery.

Tip

Clean the battery posts and terminals with a wire brush to ensure a positive connection for current flow.

Ensure the battery ground terminal is properly attached to the lawn mower frame.

Related Articles

How to Troubleshoot MTD Rider Solenoid Mowers
How to Troubleshoot MTD Rider Solenoid Mowers
How to Use a Volt Meter to Check the Neutral & Ground
How to Use a Volt Meter to Check the Neutral & Ground
How to Test the Cub Cadet 2135 Solenoid
How to Test the Cub Cadet 2135 Solenoid
How to Test a Lawn Mower Battery
How to Test a Lawn Mower Battery
How to Do I Test a John Deere 110 Ignition Switch
How to Do I Test a John Deere 110 Ignition Switch
How to Change a Starter on a Craftsman Tractor
How to Change a Starter on a Craftsman Tractor
How to Diagnose Starter Problems for a John Deere Lawn Tractor
How to Diagnose Starter Problems for a John Deere Lawn...
How to Troubleshoot a John Deere Gator 6x4 That Won't Start
How to Troubleshoot a John Deere Gator 6x4 That Won't...
How to Install Lights on a Mower
How to Install Lights on a Mower
How to Test the Ignition Module for John Deere Lawn Tractors
How to Test the Ignition Module for John Deere Lawn...
How to Troubleshoot a Yardman Riding Lawn Mower
How to Troubleshoot a Yardman Riding Lawn Mower
The Starter Relay and Why a Mower Won't Start
The Starter Relay and Why a Mower Won't Start
How to Wire a Briggs & Stratton Alternator
How to Wire a Briggs & Stratton Alternator
Garden Guides
×