How to Bury Electrical Wire

Overview

Sometimes electrical wire needs to be run from the main building to an outlying area such as a work shed, studio or a lamp post. The best solution is usually to run the wires underground to the place that needs the electricity. This can be done safely and at a reasonable cost and is much safer than placing the electric wires above ground.

Step 1

Install an electrical box at each end of the outdoor run. One box will go just inside the main building and the other will go on the inside of the outdoor structure (a lamp post has its own built-in electrical box). Check with the electrician, who is doing the electrical work, to make sure the location of each box is correct.

Step 2

Dig a trench that is at least 1 foot deep and runs in a straight line from the main building to the outside location. Place all the dirt next to to trench in neat piles. Make sure the trench comes up to the edge of the building at a point that is right below the electrical box that will receive the wire.

Step 3

Lay out the PVC pipe in the bottom of the trench with a straight coupling placed between each length of pipe.

Step 4

Run the wire through the pipe and the coupling joints. Use 12-gauge three strand underground cable (the label will read, 12/3 UL). You can buy the wire by the spool, so that the distance is covered by a single piece of wire. The wire should continue upwards into the box with at least a foot left over at each end so the electrician has plenty of wire to work with. Leave the wire loose for the time being.

Step 5

Connect all the pieces of PVC pipe together by coating both ends of the inside of the couplings with PVC cement and sliding the lengths of pipe together. At each end of the entire length of PVC you will need to attach one last straight coupling. At this point in time, just put the joint cement on one end of the coupling and slide that end onto the end of the last pipe in the long chain. Now you should have a straight run of PVC pipe that covers 90 percent of the trench. The entire length will have one piece of cable running through the pipe with enough wire left over to continue the line into the building and up to the electrical box.

Step 6

Measure from the edge of the PVC pipe to the end of the trench. Subtract 4 inches from the measurement and cut a length of PVC pipe to that length. Do this for both ends of the pipe.

Step 7

Coat both ends of the PVC pipe (the one you just cut in Step 6) with the cement. Then slide one end of the straight piece of plastic pipe into a 90-degree elbow. Now slide the two connected pieces over the wire with the long end going first. Slide the whole unit along the course of the wire until it reaches the coupling at the end of the pipe that is sitting at the bottom of the trench. Join this piece to the PVC pipe in the trench. Do this on both ends of the trench. Now the length of the trench has a complete length of pipe with a 90-degree elbow at each end and a long piece of wire coming out of each elbow.

Step 8

Measure the distance from the elbow to the surface of the ground and cut a piece of straight PVC pipe to this length.

Step 9

Coat the outside of one end with the PVC cement and slide that piece into the top of the elbow. Make sure the wire runs through the center of the pipe.

Step 10

Take a PVC cap (do this at both ends) that fits at the end of a 1 1/2 inch pipe and drill a 3/4-inch hole in the center of the cap with an electric drill. Without adding any PVC cement, slide the end of the wire through the hole in the cap and push the cap until it comes to the top of the pipe at the surface of the ground. Push the cap so it fits over the end of the pipe. Don't glue it so the electrician can add a wire coupling. Now you can fill the trench with earth.

Tips and Warnings

  • Check local building codes for regulations concerning underground wires.

Things You'll Need

  • Shovel
  • Pick
  • Hoe
  • 1 1/2 inch PVC plastic pipe
  • PVC couplings (straight and 90 degree)
  • PVC pipe caps
  • PVC cement
  • Outdoor wire (12/3 UL)
  • Wire cutters
  • Electric drill
  • 3/4-inch drill bit

References

  • Dulley: How To Install Outdoor Wiring
  • Home Envy: Installing Underground Wire
  • Electrical Hardware Store: How To Install Outdoor Lighting
Keywords: burying electric wire, underground wire, underground electrical circuits

About this Author

Henri Bauholz is a professional writer covering a variety of topics, including hiking, camping, foreign travel and nature. He has written travel articles for several online publications, and his travels have taken him all over the world, from Mexico to Latin America and across the Atlantic to Europe.

Article provided by eHow Home & Garden | How to Bury Electrical Wire